| |
Main
Date: 07 Oct 2006 11:33:53
From:
Subject: how to glue a vinyl lamination to particle board
|
I have a particle board shelf where the vinyl lamination has partially
come off on the front of it (1/2" height strip that runs for the 24"
length of the shelf) I'm trying to fix it, but I am unsure of what
type of glue was originally used.
The existing glue dried white, if that is any help :(
Does anyone have any suggestions on how to spot repair the vinyl
lamination that is lifting? The lamination came off the glue because
we were pulling a cardboard box from the shelf and it was catching the
edge of the vinyl and eventually peeled part off about a 12" section of
it. There is no glue on the vinyl, it is all still on the particle
board.
|
|
| |
Date: 07 Oct 2006 20:30:50
From: CC
Subject: Re: how to glue a vinyl lamination to particle board
|
<ojasrege@yahoo.com > wrote in message
news:1160246033.866378.164850@m7g2000cwm.googlegroups.com...
>I have a particle board shelf where the vinyl lamination has partially
> come off on the front of it (1/2" height strip that runs for the 24"
> length of the shelf) I'm trying to fix it, but I am unsure of what
> type of glue was originally used.
>
> The existing glue dried white, if that is any help :(
>
> Does anyone have any suggestions on how to spot repair the vinyl
> lamination that is lifting? The lamination came off the glue because
> we were pulling a cardboard box from the shelf and it was catching the
> edge of the vinyl and eventually peeled part off about a 12" section of
> it. There is no glue on the vinyl, it is all still on the particle
> board.
3MT Hi-Strength 90 Spray Adhesive
http://www.ellsworth.com/display/productdetail.html?productid=1203&Tab=Products
CC
|
| |
Date: 07 Oct 2006 12:16:41
From: Dave Bugg
Subject: Re: how to glue a vinyl lamination to particle board
|
ojasrege@yahoo.com wrote:
> Does anyone have any suggestions on how to spot repair the vinyl
> lamination that is lifting?
A bit of a silicone caulk adhesive would work just fine.
--
Dave
www.davebbq.com
|
| |
Date: 08 Oct 2006 14:07:21
From: Tim W
Subject: Re: how to glue a vinyl lamination to particle board
|
<ojasrege@yahoo.com > wrote in message
news:1160246033.866378.164850@m7g2000cwm.googlegroups.com...
> I have a particle board shelf where the vinyl lamination has partially
> come off on the front of it (1/2" height strip that runs for the 24"
> length of the shelf) I'm trying to fix it, but I am unsure of what
> type of glue was originally used.
>
> The existing glue dried white, if that is any help :(
>
> Does anyone have any suggestions on how to spot repair the vinyl
> lamination that is lifting? The lamination came off the glue because
> we were pulling a cardboard box from the shelf and it was catching the
> edge of the vinyl and eventually peeled part off about a 12" section of
> it. There is no glue on the vinyl, it is all still on the particle
> board.
>
IIUC you have vinyl edge-banding coming off a melamine board. It is normally
glued on with hot melt glue so sticking it back is as easy as pie. A clothes
iron, set not too hot will warm the glue enough to press it back on. a piece
of paper will keep the glue off the iron. Trim the edge with a sharp knife
or very fine abrasive paper if you need to.
Tim w
|
|
