| |
Main
Date: 09 Oct 2006 13:25:32
From: cayvman
Subject: Jessem Router Plate and Table
|
I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
fits the table insert, however, the plate does not lay level with the
table. How does one adjust the plate so that it sits level with the
table top. The Jessem Master Plate has adjustments but none that I can
see or figure out on the "plain" Router Plate. Any help or suggestions
would be appreciated. I have tried contacting Jessem but haven't gotten
a response yet.
|
|
| |
Date: 10 Oct 2006 02:50:20
From: George Max
Subject: Re: Jessem Router Plate and Table
|
On 9 2006 13:25:32 -0700, "cayvman" <cayvman@dslextreme.com >
wrote:
>I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
>fits the table insert, however, the plate does not lay level with the
>table. How does one adjust the plate so that it sits level with the
>table top. The Jessem Master Plate has adjustments but none that I can
>see or figure out on the "plain" Router Plate. Any help or suggestions
>would be appreciated. I have tried contacting Jessem but haven't gotten
>a response yet.
Like gkemper said: If the plate itself does not have leveling screws,
the solution is to put screws at each corner of the table where the
insert fits. This is how the Rockler insert is leveled. In fact,
Rockler has some nice screws for this purpose. Blunt ended, not
pointy sharp like typical wood screws.
|
| |
Date: 09 Oct 2006 16:11:48
From: cayvman
Subject: Re: Jessem Router Plate and Table
|
Gary,
Thanks for your reply, however, I don't have the Mast R plate, I have
the Rout R plate.
Are the screws on the underside of the Mast R plate?
gkemper@hotmail.com wrote:
> On 9 2006 13:25:32 -0700, "cayvman" <cayvman@dslextreme.com>
> wrote:
>
> >I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
> >fits the table insert, however, the plate does not lay level with the
> >table. How does one adjust the plate so that it sits level with the
> >table top. The Jessem Master Plate has adjustments but none that I can
> >see or figure out on the "plain" Router Plate. Any help or suggestions
> >would be appreciated. I have tried contacting Jessem but haven't gotten
> >a response yet.
>
>
> The Mast R plate I have has a black piece in each corner with a screw
> for adjustment.
>
> Gary
|
| | |
Date: 10 Oct 2006 00:40:28
From:
Subject: Re: Jessem Router Plate and Table
|
On 9 2006 16:11:48 -0700, "cayvman" <cayvman@dslextreme.com >
wrote:
>Gary,
>Thanks for your reply, however, I don't have the Mast R plate, I have
>the Rout R plate.
>Are the screws on the underside of the Mast R plate?
>gkemper@hotmail.com wrote:
>> On 9 2006 13:25:32 -0700, "cayvman" <cayvman@dslextreme.com>
>> wrote:
>>
>> >I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
>> >fits the table insert, however, the plate does not lay level with the
>> >table. How does one adjust the plate so that it sits level with the
>> >table top. The Jessem Master Plate has adjustments but none that I can
>> >see or figure out on the "plain" Router Plate. Any help or suggestions
>> >would be appreciated. I have tried contacting Jessem but haven't gotten
>> >a response yet.
>>
>>
>> The Mast R plate I have has a black piece in each corner with a screw
>> for adjustment.
>>
>> Gary
Yes, they are. Sorry about the mix-up.
If you have no adjustments on the plate itself, you can add some
screws to the inside corners of the rabbited top.
Gary
|
| |
Date: 09 Oct 2006 22:57:45
From:
Subject: Re: Jessem Router Plate and Table
|
On 9 2006 13:25:32 -0700, "cayvman" <cayvman@dslextreme.com >
wrote:
>I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
>fits the table insert, however, the plate does not lay level with the
>table. How does one adjust the plate so that it sits level with the
>table top. The Jessem Master Plate has adjustments but none that I can
>see or figure out on the "plain" Router Plate. Any help or suggestions
>would be appreciated. I have tried contacting Jessem but haven't gotten
>a response yet.
The Mast R plate I have has a black piece in each corner with a screw
for adjustment.
Gary
|
| |
Date: 10 Oct 2006 08:03:38
From: cayvman
Subject: Re: Jessem Router Plate and Table
|
Thanks all. Went home last night and looked in the original packing and
lo and behold there was 8 set screws and an allen wrench. Funny thing,
though, that in all "manual" it says nothing about the leveling screws.
The only reference to them is on the label of the packing box.
George Max wrote:
> On 9 2006 13:25:32 -0700, "cayvman" <cayvman@dslextreme.com>
> wrote:
>
> >I purchased the Jessem Rout R plate and Jessem Mast R Top. The plate
> >fits the table insert, however, the plate does not lay level with the
> >table. How does one adjust the plate so that it sits level with the
> >table top. The Jessem Master Plate has adjustments but none that I can
> >see or figure out on the "plain" Router Plate. Any help or suggestions
> >would be appreciated. I have tried contacting Jessem but haven't gotten
> >a response yet.
>
> Like gkemper said: If the plate itself does not have leveling screws,
> the solution is to put screws at each corner of the table where the
> insert fits. This is how the Rockler insert is leveled. In fact,
> Rockler has some nice screws for this purpose. Blunt ended, not
> pointy sharp like typical wood screws.
|
|
